November 11, 2026
Updated November 14, 2026

Freight Class Chart: How to Calculate Your LTL Freight Class (2026)

Freight Class Chart: How to Calculate Your LTL Freight Class (2026)

Freight class is the rating, from 50 to 500, that LTL carriers use to price a shipment. Since July 19, 2025 many commodities are classed by density on a 13-step scale. To find yours, multiply length x width x height in inches, divide by 1,728 to get cubic feet, divide the weight in pounds by that number, and read the chart below. A 600 lb pallet measuring 48 x 40 x 48 inches works out to 11.25 lbs per cubic foot, which is class 92.5.

Quick answer: Denser freight gets a lower class and a lower rate. Class 50 is the cheapest and applies at 50 lbs per cubic foot or more. Class 400 applies below 1 lb per cubic foot. Not every item is rated on density alone, so confirm your commodity in the National Motor Freight Classification before you put a class on the bill of lading.

Sources: NMFTA Classification 101; NMFTA Docket 2025-1 announcement; FedEx NMFC density scale; NMFTA data update schedule; PITT OHIO rules tariff Item 1014; Old Dominion Accessorial Services (tariff ODFL 100-Q, effective October 5, 2026). Checked November 11, 2026.

Freight Class Chart: The 13-Step Density Scale

Density (lbs per cubic foot)Freight class
Less than 1400
1 but less than 2300
2 but less than 4250
4 but less than 6175
6 but less than 8125
8 but less than 10100
10 but less than 1292.5
12 but less than 1585
15 but less than 22.570
22.5 but less than 3065
30 but less than 3560
35 but less than 5055
50 or greater50

This is the scale the National Motor Freight Traffic Association (NMFTA) put in place with Docket 2025-1, as published by FedEx Freight. It replaced an older 11-step scale. The classification itself runs up to class 500, so not every class appears on the density scale.

How to Calculate Freight Class

  1. Measure the handling unit as shipped. Length, width and height in inches, including the pallet and any packaging.
  2. Get cubic feet. Multiply length x width x height and divide by 1,728.
  3. Get density. Divide the weight in pounds, including the pallet, by the cubic feet.
  4. Read the chart. Find the row your density falls in.
Pallet (inches)WeightCubic feetDensityClass
48 x 40 x 48600 lbs53.311.25 lbs/cu ft92.5
48 x 40 x 60400 lbs66.76.00 lbs/cu ft125
48 x 40 x 361,000 lbs40.025.00 lbs/cu ft65
48 x 40 x 72300 lbs80.03.75 lbs/cu ft250

Freight Class Lookup for a Standard 48 x 40 Pallet

If you ship on standard 48 x 40 inch pallets, this table does the math for you. Find the total height, including the pallet, and the total weight.

Total weight36 in. tall48 in. tall60 in. tall72 in. tall
250 lbsClass 125Class 175Class 250Class 250
500 lbsClass 85Class 100Class 125Class 125
750 lbsClass 70Class 85Class 92.5Class 100
1,000 lbsClass 65Class 70Class 85Class 85
1,500 lbsClass 55Class 65Class 65Class 70
2,000 lbsClass 50Class 55Class 65Class 65

The pattern is the point. The same 500 lbs is class 85 on a 36 inch pallet and class 125 on a 72 inch pallet. Height you do not need costs you a class or two.

Measuring Rules That Change Your Class

  • The pallet counts. PITT OHIO’s rules tariff computes density from each skid’s weight including packaging and pallets, and its dimensions as tendered.
  • Freight that cannot be stacked is measured taller. PITT OHIO uses a height of at least 96 inches for freight that cannot have other freight loaded on top. A short pallet marked “do not stack” can be rated as if it were 8 feet tall.
  • Mixed pallets take the worst class. Under NMFC shipment rule 640, if a pallet holds items in different classes and the bill of lading does not itemize them, the carrier classes the whole pallet at the least favorable class on it.
  • Measure after wrapping. Overhang and bulging stretch wrap are part of the dimensions the carrier will measure.

More on this in why pallet dimensions matter more than weight.

NMFC Codes: When Density Is Not the Whole Answer

The National Motor Freight Classification assigns every commodity an item number and a class. NMFTA’s Freight Classification Development Council weighs four characteristics: density, handling, stowability and liability. Two items with the same density can land in different classes if one is fragile, hazardous or awkward to load.

You look up an item in the NMFC book or in ClassIT+, NMFTA’s online version, which includes a density calculator. NMFTA says specific descriptions take precedence over general ones, and that notes attached to an item can add conditions or exclude commodities.

The classification keeps changing. The council meets three times a year. After the July 2025 overhaul, NMFTA’s schedule shows the next supplement, 2026-1, took effect on May 23, 2026. If you set your classes before then, check them again.

What Happens If the Class Is Wrong or Missing

  • Missing class: Old Dominion’s tariff says a bill of lading with no class or description defaults to class 100.
  • Wrong class or weight: the carrier may inspect and reweigh the freight, and the customer is liable for charges based on the correct description and weight. This is the reweigh and reclass adjustment on a freight invoice.
  • Fixing it afterward: Old Dominion charges $45 for a corrected bill of lading.
  • Very light freight: Old Dominion applies a separate minimum charge to low-density freight, under 3 lbs per cubic foot at 350 to 749 cubic feet, or under 6 lbs per cubic foot at 750 cubic feet or more.

How to Get a Lower Freight Class

  • Cut height. Use the shortest pallet build that is stable. Every inch of air lowers density.
  • Make it stackable. A flat, solid top avoids the 96 inch rule.
  • Itemize mixed pallets on the bill of lading so one high-class item does not set the class for everything.
  • Ask about FAK. A freight-all-kinds provision in your rate agreement bills a range of classes as one lower class.

Freight class is the LTL counterpart of dimensional weight in parcel shipping. For boxes under about 150 lbs, see how to calculate dimensional weight or use our dimensional weight calculator. For how class fits into the full LTL rate, see what LTL shipping is and how it is priced.

Frequently Asked Questions

What is freight class?

Freight class is the rating LTL carriers use to price a shipment, from class 50 (least expensive) to class 500. It comes from the National Motor Freight Classification and is based on density, handling, stowability and liability.

How do I calculate freight class?

Multiply length x width x height in inches, divide by 1,728 to get cubic feet, then divide the weight in pounds by the cubic feet. That gives density in lbs per cubic foot, which you match to the 13-step density scale.

What freight class is a standard pallet?

It depends on weight and height. A 48 x 40 x 48 inch pallet weighing 600 lbs has a density of 11.25 lbs per cubic foot, which is class 92.5. The same pallet at 1,000 lbs is class 70.

What is the lowest freight class?

Class 50. On the density scale it applies to freight at 50 lbs per cubic foot or more, and it carries the lowest rate.

What is an NMFC code?

It is the item number the National Motor Freight Classification assigns to a commodity, along with its class. You look it up in the NMFC book or in ClassIT+, NMFTA’s online tool.

What happens if I use the wrong freight class?

The carrier can inspect and reweigh the shipment and bill you at the correct class and weight. At Old Dominion, a bill of lading with no class defaults to class 100, and a corrected bill of lading costs $45.

Did freight classes change in 2025?

Yes. NMFC Docket 2025-1 took effect on July 19, 2025. It moved many commodities to density-based classes and replaced the 11-step density scale with a 13-step scale. Further changes took effect on May 23, 2026.

Related Reading

Get a free freight and parcel invoice audit

D’Arrigo Consulting audits carrier invoices line by line for billed class, billed weight and accessorials that do not match what was quoted. Request a free invoice audit to see what you can recover.

This article is for informational purposes only. Carrier rates, surcharges and policies change frequently. Always verify current terms directly with the carrier for your specific situation. Have questions? Reach out to us.

Paul D'Arrigo, author

Meet the Author

paul@darrigoconsulting.com
I’m Paul D’Arrigo. I’ve spent my career building, fixing, and scaling operations across eCommerce, fulfillment, logistics, and SaaS businesses, from early-stage companies to multi-million-dollar operators. I’ve been on both sides of growth: as a founder, an operator, and a fractional COO brought in when things get complex and execution starts to break
Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form.